NG-9 PLUS

NG-9 PLUS

All the innovative features of NG-9 with new potential

NG FamilyData sheetRequest information and prices



NG Family

NG-9/96 - Three Multifunction meters in only 1 device
NG-9 – 9 measured lines in a single device
NG-9 PLUS
NG-Gateway – Gateway to collect, store and send data to Server
NG-TH169 - Room Temperature and Humidity 169MHz radio sensor
NG-W169 - 169MHz Radio Receiving module
NG-Rio - Loads’ remote control
NG-IoT - RS-485/Wi-Fi Transparent Converter
NG-IO - Digital Input/Output remote module

 

Features

The world’ smallest analyzer featuring 9 channels within 9 cm, to reduce installation time and costs by a third and multiply performance by 3?

      • Flexibility: special sensors ranging 1 to 8000 A offer the most versatile solution available on the market
      • Accuracy: 0.5 class guaranteed on the entire measurement system
      • Measurements: 160 electric parameters via RTU-Modbus
      • Versatility: High suitability thanks to the combination of split current transformer and/or Rogowski sensors for single-phase, three-phase or mixed mode
      • Simplicity: time and costs are reduced by 85% with no need for plants shutdowns

Nothing compares to NG-9 PLUS.

      • Connect sensors to acquire Temperature, Status, and Digital signals
      • Measure up to the 15° Harmonic and THD on all 3 VOLTAGE channels
      • Measure up to the 15° Harmonic and THD on all 9 CURRENT channels
      • No plants shutdown
      • Modbus RTU communication 3 times faster than other analyzers: 115200 baud rate
      • Use all range of Rogowski or Split Current sensors on each instrument on either single, three or mixed phase mode
      • Easily fits in pre-existing panels
      • Connection to 1 voltmeter instead of 3
      • Extensions allow up to 10 m distance from the device
      • Reduced installation errors for a simple and correct start up
      • Each current sensor can be connected to the device with a one-way electrical connector without additional cables, scissors and screwdrivers
      • Power consumption 12 times lower than any other device on the market. i.e. : NG-9 €21/10 years, other devices €252/10 years
      • Set up software for simple and fast programming
      • Fields of application: office buildings, warehouses, retail centres, small and large factories; it is particularly suitable for data centres’ energy cost distribution

Available sensors

New Generation sensors, available for NG-9 PLUS

NG-AIN

This sensor provides the NG-9 system with an analogic ISOLATED voltage or current Input

  • Flow range: ±10V, 0-10V, ±20mA, 0-20mA and 4-20mA selectable straight from the instrument;
  • Measure isolation: dielectric strength of 1kV between Input and instrument to simplify use and improve protection against disturbance and the system’s overall security;
  • Accuracy: on the entire measuring chain is 0,2% of the reading plus 0,05% of the flow;
  • Measurement field: between 0 and 120% of the flow. Maximum permanent overload capacity 400% of the flow for current measurements and 100V (1000%) for voltage measurements.

NG-DIG

This sensor provides the NG-9 system with an ISOLATED Input for digital signal acquisition from passive Outputs (PNP, NPN, OPTOMOS or electromechanical contacts) as well as active AC or DC Outputs from 12 to 110 Vdc or Vac

  • Acquisitions: the system can acquire, ON-OFF static signals as well as pulses coming from meters up to 10Hz frequency with a minimum pulse’s duration of 5 milliseconds (10 milliseconds for AC Input);
  • Measure isolation: dielectric strength of 1kV between Input and instrument to simplify use and improve protection against disturbance and the system’s overall security.

NG-RTD

This sensor provides the NG-9 system with an ISOLATED Input for Temperature measurement with RTD sensors (i.e. PT100). NG-9 PLUS is compatible with PT100 (standard), PT200, PT 500 and PT1000

  • Measure isolation: dielectric strength of 1kV between Input and instrument to simplify use and improve protection against disturbance and the system’s overall security;
  • Accuracy: on the entire measuring chain is ±0,2% for readings between -100°C and +200°C, with a typical accuracy of ±0,1 % for readings between -20°c and +100°C.

Standard sensors

RG2K Flexy – Rogowski sensor

  • Openable and flexible sensor
  • Standard diameter: 100mm
  • Selectable ranges: 100, 200, 400, 1000, 2000A
  • On request: from 200 to 850 mm diameter
  • Selectable range: up to 8000 A
  • Output Cable: 5 m, shielded
  • Accuracy: Class 0,5
  • Single and three-phase measurement (3 probes)
  • Removable terminal

CC24 Sensor – Standard size current clamp

  • Dimension (LxHxW) 44,5 x 65 x 33,5 mm
  • Cable window ≤ 24 mm
  • Output Cable: 2 m
  • Single and three-phase measurement (from 1 to 3 transformers)
  • Selectable range: 20, 40, 80, 200A

CC16 Sensor – Miniature size current clamp

  • Dimension (LxHxW) 30 x 43,5 x 30 mm
  • Cable window ≤ 16 mm
  • Output Cable: 2 m
  • Single and three-phase measurement (from 1 to 3 transformers)
  • Selectable range: 10, 20, 40, 100A

CC06 Sensor – Mini-current clamp

  • Dimension (LxHxW) 16 x 32 x 26,4 mm
  • Cable window ≤ 6 mm
  • Output Cable: 2m
  • Single and three-phase measurement (from 1 to 3 transformers)
  • Selectable range: 1, 2, 5, 10A

 
 
 

Strong points

 

Installation

 

 

Related Products

NG-Gateway – Gateway to collect, store and send data to Server

NG-TH169 – Room Temperature and Humidity 169MHz radio sensor

NG-W169 – 169MHz Radio Receiving module

NG-IoT – RS-485/Wi-Fi Transparent Converter

NG-IO – Digital Input/Output remote module

NG-9 – 9 measured lines in a single device

 

Correlated Products

 

Management and Control Software Energy Sentinel Web .

Energy Sentinel WEB is an application Server which allows you to get an access via remote to acquired data and to analyze them, through simple and intuitive WEB pages. The use of this WEB application on a Server makes possible the best security concerning the availability and reliability of the system, allowing also a plant control to the highest performance of energy efficiency (KPI).

Our SW is in constantly evolving, with frequent updates adding new features to the platform. The dealing with the software with every kind of instrument, meter or device, allows you to avoid HW replacement in existing plants. ISO 50001 certified companies, system integrators, energy managers, energy consulting firms and ESCO can take significant advantages by using the platform.

The software, was born to be multi-user and multi-site, and it allows the following functions:

    • Displaying data on the Web, using the standard http protocol through any browser (Explorer, Chrome, Safari, Firefox). Possibility to enable the encryption of the connection through https protocol
    • Checking the stored data by accessing anytime through any Web point, thanks to User-ID and a Password, without installing additional programs
    • Configuring entirely the access to data on the Web, setting for each user the access mode to various areas
    • Manage the data from many devices geographically far from each other.
    • The platform versatility allows you to integrate devices and instruments “from third people” by means of their system protocol.
    • The Consultation Interface is also optimized for I-pad and Tablet.

Through its graphical interface, simple and intuitive, it’s also possible to:

    • Realize and compare graphics, histograms and diagrams
    • Advanced data displaying with graphics such as Carpet Plot, Scatter Plot and Periods Comparison
    • Compare data with different full-scale among them
    • Customizable Dashboard
    • Reports creation with the possibility of sending automatic emails
    • Create of mathematical modules to open virtual channels
    • Display fully configurable real-time data
    • Display fully configurable graphics
    • Display summaries of period
    • Share of the consumptions in bands
    • Set the type of fields you want to see: histograms, linear graphics, flow charts, etc.
    • Display historical data on a freely-selectable time interval, as a line graphic or column diagram, showed with two vertical axes
    • Arrange data in tables
    • Export data as CSV format for Excel
    • Set and create groups and subgroups for data coming from the controlled plants (unlimited number of levels)
    • Set alarm thresholds, with possibility to send SMS and e-mail if the threshold values set are exceeded
    • Set and display of the tariff
    • Alarms on closing and opening contacts and thresholds with hysteresis

 

This website uses cookies, either its own and third parties’ to offer you the best browsing experience and related utilities: to view the full disclosure and/or deny your consent to all or some cookies, please see the cookie policy. By continuing browsing without changing the settings, closing this banner, scrolling this page or clicking on any of its links or elements, you agree to the use of cookies.
Ok